Pipetting aids

Pipette controllers from BRAND provide precise control for accurate volume setting and delicate culture work. The pipetting aids provide multiple user selectable pipetting modes as well as multible pipetting speeds. Pipette controllers are indispensable for daily tasks in cell culture, pharmaceutical and chemistry labs. Choose between different pipetting aids like the accu-jet® S with an integrated rest position, macro, micro or pipette fillers with two or three valves.

Sort by

Pipette controllers accu-jet^® S
Promotion

Rating:
87%

3 Reviews

Sale

statt 444,70 €

nur 289,06 €
Pipette controllers macro, 0,1 ml - 200 ml, incl. spare membrane filter 3 μm

ab 62,35 €
Pipette controllers micro-classic

ab 54,25 €
Pipette fillers, natural rubber

ab 16,75 €
Membrane filter accu-jet^® S / pro / macro pipette controller

ab 6,25 €
Silicone adapter micro-classic pipette controller

ab 11,95 €
NiMH battery pack accu-jet^® S / pro

ab 17,25 €
Replacement valve system macro pipette controller

ab 26,95 €
Suction bellow macro pipette controller, with screw ring, silicone

ab 18,70 €
Adapter accu-jet^® S / pro / macro pipette controller

ab 4,20 €
Replacement suction system micro pipette controller

ab 33,05 €
Snap tape accu-jet^® S

ab 11,10 €

Back

Frequently Asked Questions (Pipetting aids)

Is the membrane filter autoclavable?

The membrane filter is autoclavable up to 5 times at 121 °C (2 bar) with a holding time of at least 15 minutes.

What is the purpose of the small blow-out bellows?

When using blow-out pipettes the last drops in the tip of the pipette must be dispensed, as well. To do so the small blow-out bellows should be pressed once as soon as the meniscus in the pipette tip comes to a standstill. If other pipette types are used, the residue has to remain in the pipette tip to have the correct volume dispensed. The blow-out bellows should then only be used to blow out residual liquid after the work is done.

What should be done if the pipette drips in the accu-jet® pro?

If the filter is not properly positioned (with the larger diameter fitting in the silicone pipette adapter), please insert the filter properly. If this action does not lead to a solution, check if adapter or valve system are damaged and replace the items if necessary.

What can be done if the accu-jet® pro does not properly hold the pipette?

Please check if adapter is dirty or damaged. Eventually clean or replace the adapter.

What should be done if the pipette has been overfilled with the macro?

The adapter has to be cleaned and the membrane filter has to be replaced. Wear protective gloves and eye protection. Avoid the risk of contamination! Pull out the pipette, unscrew the adapter support, pull out the membrane filter, and remove adapter from adapter support by pushing it upwards. To clean adapter, carefully rinse it by using an appropriate compatible solvent (e.g., water) in a wash bottle. Blow out the liquid and allow to dry completely.. Place the new membrane filter with the thicker end facing downwards into the adapter (with the smaller conical side up). Screw in the adapter support hand tight and autoclave if necessary. Consult the Manual to see the instruction with illustrations!

How should the macro be cleaned?

When properly used, the instrument is maintenance-free. If necessary, the housing can be wiped down with a damp cloth.

Which modes for dispensing can be selected at the accu-jet® pro?

Select mode Switch up: Gravity-delivery Switch down: ▼ Blow-out (with motor power)

Can the accu-jet® pro be used during recharging?

Yes, the instrument can be used during recharging. During recharging, the LED on the instruments lights up continuously. When the recharging is completed the LED flashes every 15 seconds.

How can the pipette controller be tested for leaks?

First fill the pipette and hold it vertically. After adjusting the meniscus, no liquid may drip from the pipette without actuating the valves.